Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterLiftMaster Torsion Spring Replacement: The Georgetown Owner’s Guide
LiftMaster torsion spring replacement in Georgetown typically runs $180-$340 installed, and we carry the right springs for most LiftMaster door systems on our trucks. Most replacements are finished in a single visit. You’ll usually discover the problem when the door won’t lift, lifts unevenly, or slams shut - the spring that carries the door’s entire weight has snapped or lost tension.
Which LiftMaster Models This Applies To
LiftMaster does not manufacture its own torsion springs. The company sources springs matched to the door’s weight and lift type, not the opener model itself. What matters is the door’s size, material, and spring configuration - usually marked on a label inside the door or on the winding cone.
We see three common setups on Georgetown homes: standard 2-inch diameter springs for steel doors up to 16 feet wide, high-lift configurations for taller ceilings common in newer Sun City builds, and duplex spring systems on heavier insulated doors. The critical spec is the wire gauge and coil length. A 0.250 wire by 32-inch spring carries a different load than a 0.243 by 28-inch, and swapping them causes premature failure or dangerous over-torque.
LiftMaster-branded springs are OEM-spec from third-party manufacturers. We stock quality aftermarket equivalents rated to the same cycle life - typically 10,000 cycles - at the same or better spec. The difference is price and availability, not safety. Mainspring Garage Door Co. is an independent service provider, not affiliated with LiftMaster.
Signs Your LiftMaster Torsion Spring Replacement Is Failing
- The door feels heavy or won’t stay open. A torsion spring stores energy to offset the door’s weight. When coils fatigue, that balance disappears. The opener strains, the cables go slack, and the door drifts down from the open position.
- You hear a loud bang from the garage. That’s the spring snapping, often at the anchor cone where stress concentrates. In Georgetown’s heat, metal fatigue accelerates - we see more spring failures in August than any other month.
- The door opens crooked or one cable hangs loose. A broken spring on one side of a dual-spring system throws the door off balance. The remaining spring carries double load and will fail soon after.
- A visible gap in the spring coils. A healthy torsion spring has tightly wound coils. A gap of even an inch means a fracture inside the coil body. Do not operate the door.
- The opener motor runs but the door barely moves. LiftMaster openers have force-limiting protection. When the spring fails, the opener detects excessive load and reverses or stalls to protect the motor gears.
Replacement Cost & What’s Included
| Service | Price Range in Georgetown |
|---|---|
| Single torsion spring replacement | $180-$260 |
| Dual spring replacement (both springs) | $280-$340 |
The price depends on wire size, door weight, and whether we replace one spring or both. We always recommend pairing springs - when one fails, the other has the same cycle count and will follow shortly. Every quote includes the spring, winding and anchor cones, lubrication, balance adjustment, and safety cable inspection. We state the flat price before touching a tool. The work is covered by our 90-Day Done Right Promise, in writing, with no dispute process.
DIY or Call Us?
There’s a safe check and an unsafe repair. You can verify the symptom: pull the red emergency release, lift the door manually. If it weighs 150 pounds instead of 15, the spring has failed. That’s useful information to tell us when you call.
What you should not do is unwind or install a torsion spring yourself. These springs hold lethal tension - a winding bar slipping free can cause serious injury or worse. The cones, cables, and brackets are under simultaneous load in directions that aren’t obvious until something moves wrong. We’ve been called to fix DIY attempts that damaged the door, the opener, or worse. Tell me what it’s doing. We’ll go from there.
Carl Dutton and our crew carry the right springs, the right winding bars, and the training to match the spec exactly. Most Georgetown jobs are done in one visit. Call (737) 257-5760 for a free estimate.
FAQs
Standard springs are rated for 10,000 cycles - roughly 7-10 years for a typical Georgetown household. Sun exposure and temperature swings in Williamson County shorten that by stressing the metal. Call (737) 257-5760 if your spring is past year seven; we can check remaining cycle life during a tune-up.
No. A fatigued or fractured spring cannot be safely spliced, welded, or re-tensioned to original spec. Replacement is the only proper repair. We stock springs for same-day replacement and quote the full price before starting.
Most LiftMaster torsion spring replacements take 45-60 minutes from truck arrival to final balance check. We also inspect cables, rollers, and opener force settings while we’re there. Call (737) 257-5760 to schedule.
Yes. We stock torsion springs for standard residential door widths from 8 to 18 feet, in wire sizes from 0.207 to 0.295, plus the cones and hardware that match. For odd sizes or custom doors, we source overnight from our Austin supplier. Most Georgetown jobs need no second trip.
Written by Carl Dutton, Owner, Mainspring Garage Door Co. at Mainspring Garage Door Co., serving Georgetown and nearby areas.